Salt Spray Test is a standardized and popular corrosion test method, used to check
corrosion resistance of materials and surface coatings.
Usually, the materials to be tested are metallic and finished with
a surface coating which is intended to provide a degree of
corrosion protection to the underlying metal.
CNS: 3627, 3385, 4159, 7669, 8886.
JIS: D0201, H8502, H8610, K5400, Z2371.
ISO: 3768, 3769, 3770.
ASTM: 8117, B268.
|Specifications (Note: We reserve the right to change specifications
without prior notice)|
|Interior dimensions(W*H*D)mm||1600 X 500 X 1000||1200 X 500 X 800||900 X 500 X 600||600 X 400 X 450|
|Exterior dimensions(W*H*D)mm||2240 X 1500 X 1600||1410 X 1280 X 880||1460 X 1280 X 910||1130 X 1070 X 630|
|Salt Water Tank Volume (L)||60||40||25||15|
|Temp. range (Testing barrel)||35±1℃～50±1℃|
|Temp. range (Pressure barrel)||47±1℃～63±1℃|
|Test applicable||NSS, ACSS,CASS,CORK|
|Pressed Air Pressure||1.00±0.01kgf/cm²|
|Spray Amount||1.0~2.0ml/80cm²/h(Collect at least 16 hours, take the average)|
|Ambient Relative Humidity||More than 85%R.H.|
|PH Value||6.5~7.2 3.0~3.2|
|Spraying Manner||Programmable Spraying|
|Power||AC220V 1Φ 50Hz|
Standards implemented and met
1) GB/T 2423.17-1993 salt spray test
2) GB/T 2423.18-2000 salt spray test
3) GB/T 10125-1997 salt spray test
4) ASTM.B117-97 salt spray test
5) JIS H8502 salt spray test
6) IEC68-2-11 salt spray test
7) IEC68-2-52 1996 salt spray test
8) GB.10587-89 salt spray test
9) CNS.4158 salt spray test
10) CNS.4159 CASS Copper accelerated acid salt spray test
11) GB/T 12967.3-91 CASS Copper accelerated acid salt spray test
(1) Spray tower
(2) Funnel cup
(3) Touch screen controller
(5) Pressure gauge
(6) Metering cylinder
(1)Chamber real-time temperature
(2)Chamber temperature setting
(3)Actual test time
(4)Test time setting
(7)Machine start/stop working button
(8)Spray start/pause button
(9)Test chamber low water alarm
(10)Defog after test
(11)Salt water tank low water alarm
(12)Reduce setting value
(13)Increase setting value
(14)Pressure barrel low water alarm
(15)Non-spray time setting
(16)Spray time setting
(17)Pressure barrel temperature setting
(18)Pressure barrel real-time temperature
Test chamber temperature control: Control the chamber temperature ,
according to standard, NSS AASS test is 35℃,and CASS test is 50℃.
Pressure barrel temperature control:Control the saturated air
barrel temperature, NSS AASS is 47℃,CASS test is 63℃.
NSS AASS Test:Chamber temperature set 35℃, Pressure barrel
temperature set in 47℃(40℃-50℃).
CASS test :Chamber tember temperature set 50℃, Pressure barrel
temperature set 63℃(60℃-70℃).
Power switch:Control the whole machine power. Long press for power
on or off.
Start/stop switch:Control the heating system of test chamber, heat
sink and Pressure barrel.
Spray/pause switch:control the spray system.
Defog switch:control defog system, clear the salt mist in chamber
Test chamber low water alarm:When the water level is low, the light
will flicker . Add pure water into the test chamber until the light
Salt water tank low water alarm:When the salt water level is low,
the light will flicker.Add salt water into the salt water tank
until the light doesn,t flicker.
Pressure barrel low water alarm:When the water level is low, the
light will flicker.Add pure water into the pressure barrel nutil
the light doesn,t flicker.
Illustration on the back of the salt spray tester
KOMEG offers the newest and most modern salt fog testing chambers
for your testing requirements. KOMEG salt spray test chambers are
offered in 60 Liter, 270 Liter, 800 Liter and 960 Liter models and
are cost effective solutions to acceleratedcorrosion testing of
samples in salt fog. Models have an uncomplicated design that has
optimized the openarea to maximize the number of test coupons while
providing headroom for testing large and bulky objects
We are on line 24 hours, your any questions will get timely
effective treatment and recovery.
Depending on the size of the order and its destination, we will
find the most efficient way of delivering your order. Collect
shipments through your account at UPS, FedEx, freight forwarder of
choice or other can also be arranged. Let us know of such
arrangements with your Purchase Order.
Quotes and Orders do not include customs duties and taxes as they
vary from country to country and are the sole responsibility of the
1. Q: Have your machine met relevant standards, and with relevant
A: Yes, our machines are manufactured according to International
Standards. If TEST CERTIFICAT required, it can be offered.
2. Q: How-to vedio provided?
A : Yes, if required, our engineers will record a specialize how-to
video for you.
3. Q: Is the machine made in your own plant?
A: Yes, welcome to visit our plant(factory), also we support OEM
4. Q:How you do the maintenance oversea?
A: In the way you are convenient, by Telephone or E-mail or Vedio